System Software Update

What Does This Do?
This utility updates the system firmware and provides the following benefits:
  • Adds support for recording 60p/30p/24p/120p movies in the XAVC S format that supports high bit rates
    Note: When shooting a movie in the XAVC S format, you must use an SDXC card of Class 10 or faster.
Applicable Products and Operating Systems (see full list...)

IMPORTANT: This file is only for use with the models identified. Not all models are sold in all countries.

Table of Contents 
Determine if Your Camera Needs the Update 

This update is only for DSC-RX10 cameras that currently have firmware version 1.00. If your camera firmware version is already Version 2.00, this update is not necessary.


Check the version of your camera firmware:


  1. Power on the camera.
  2. On the camera, select "MENU", "Setup", and then "Version".
  3. If the version number is Ver. 2.00, the camera does not need this update.
    Main Settings Version Number
Important Notes 
  • This utility is only for use with the Sony® DSC-RX10 cameras. Do not install this utility with any other model.
  • WARNING!!: This firmware update and any changes incurred by it are permanent. It is not possible to return to a previous firmware version after updating this firmware. By continuing this update process and downloading and updating this firmware, you acknowledge that you are aware and understand that this update cannot be reversed.
  • This update process requires the following items for proper updating:
    • A computer with:
      • Available Hard Disk Space: 200 MB or more
      • Installed Memory (RAM): 512 MB or more
      • A USB port.
      • One of the following Microsoft® Windows® operating systems installed:
        • Windows 8/8.1
        • Windows 7 (with Service Pack 1)
        • Windows Vista® (with Service Pack 2)
          Note: Starter Edition of Windows Vista is not supported.
    • Camera power supply:
      • This update can only be performed when the remaining battery level has three bars Battery Indicater or more. When performing the firmware update, it is recommended to use a fully charged NP-FW50 rechargeable battery pack.
        WARNING!!: The camera may not operate properly if the power is interrupted during the update.
    • USB cable:
      • Use only the USB cable supplied with the camera.
        IMPORTANT: Update functionality is not guaranteed with any other USB cable.
  • IMPORTANT: You must initialize the camera after the update is complete. This will return all settings to their original default values. Please make note of any settings you have changed before performing the update.
  • To ensure that no other program interferes with the installation, save all work and close all other programs. The Taskbar should be clear of applications before proceeding.
  • It is highly recommended that you print out these instructions for use as a reference during the installation process.
Prepare the Camera for the Firmware Update 
  1. Remove the memory card from the camera
  2. Ensure the camera battery is fully charged.
  3. You must initialize the camera after the update is complete. This will return all settings to their original default values. Please make note of any settings you have changed before performing the update.
Download and Update the Firmware 
  1. Download the Update_DSCRX10V200.exe file to a temporary or download directory (please note this directory for reference).
    Note: For Windows 8/8.1, the default settings for Internet Explorer® will save the file in the "Downloads" folder. To locate the Downloads folder, click the "Desktop" tile from the Start screen and then locate the downloaded file using Windows Explorer.
  2. Go to the directory where the file was downloaded and double-click the Update_DSCRX10V200.exe file to begin the Firmware Updater.
  3. At the "Firmware Updater" screen, please follow the instructions.
  4. Power on the camera.
  5. Make sure the USB Connection Setting is set to "Mass Storage".
    On the camera, select "MENU", "Setup", "USB Connection", and then ensure "Mass Storage" is selected.
    USB Connect Screen
  6. Ensure the memory card is removed from the camera.
  7. Connect the camera to your computer using the supplied USB cable. When the camera is connected to the computer, the LCD screen of the camera turns off. Please proceed to the next step.
    Note: If the message "Could not find the camera for this update." appears on the computer display, try disconnecting and reconnection of the USB cable or try another USB port on the computer.
  8. Verify that the remove hardware icon Remove Hardware Icon or Remove Hardware Icon is displayed in the task tray at the lower right-hand corner of the computer screen.
  9. After completing the steps above, click "Next" at the "Firmware Updater" screen.
    Firmware Updater Screen
  10. WARNING!!: Do not power off the camera or disconnect the USB cable until the update process is complete.
  11. When the updater recognizes the camera connection, the next "Firmware Updater" screen is displayed on the computer, and the camera screen displays "Follow the instructions on the computer".
    camera Screen
  12. At the "Firmware Updater" screen, click "Next".
    camera Connected Screen
  13. When the following screen is displayed, check the version number at the lower left.
    Current Version Screen
    If the current version is "1.00", click "Next".
    Note: If the current version is "2.00", your camera does not need this update. Stop the USB connection by clicking the remove hardware icon Remove Hardware Icon or Remove Hardware Icon in the task tray in the lower right corner of the computer screen and then click the "Finish" button on the "Firmware Updater" screen. Then power off the camera, briefly remove the battery pack or the AC adaptor, and then power on the camera again.
  14. To perform the firmware update, follow the steps to reset the camera.
  15. Reset the camera:
    1. In the task tray at the lower right hand corner of the computer screen, click the "Safely Remove Hardware" Remove Hardware Icon or Remove Hardware Icon icon and stop the USB connection. If the icons are not displayed on the task tray, please proceed to the next step.
      IMPORTANT: Do not disconnect the camera from the computer.
    2. On the camera, press the center of the control wheel to execute reset.
      Initialize Camera
      Note: The camera screen turns off when the center of the control wheel is pushed.
  16. At the "Firmware Updater" screen, click "Next".

  17. Click Next Screen
  18. After resetting, reconnection of the camera is verified, and the next Firmware Updater screen appears.
  19. When the following screen is displayed, click "Run".
    Note: The update process takes about fifteen minutes to complete.
    Run the Update Screen
    WARNING!!: Do not power off the camera or disconnect the USB cable until the update process is complete.
  20. When the update process has been completed, the camera will automatically restart. The message "Recovering data. Please wait" may appear for a few minutes before restarting. Make sure the camera is powered on and wait until the LCD screen appears again. When the LCD screen appears, click "Finish".
    Update Complete Screen
  21. In the task tray at the lower right hand corner of the computer screen, click the "Safely Remove Hardware" Remove Hardware Icon or Remove Hardware Icon icon and stop the USB connection.
  22. You may now disconnect the USB cable.
Initialize the Camera 

Please initialize the camera after performing the update:

  1. On the top of the camera, press the "MENU" button.
  2. At the menu, select "Setup", and then "Setting Reset".
    Settings Reset menu
  3. At the "Setting Reset" screen, select "Initialize".
    Initialize menu
  4. At the "Restores settings..." message, select "OK".
    Restore Settings message
  5. At the "Performs initialization" message, select "OK".
    Performs Initialization message
  6. The camera will automatically restart after the initialization is complete.
Check the Firmware Version After Updating (optional) 

Please follow the steps below to confirm that the firmware was successfully updated:

  1. On the top of the camera, press the "MENU" button.
  2. At the menu, select "Setup", and then "Version".
  3. If the version number is Ver. 2.00, the camera firmware was successfully updated.
    Main Settings Version Number
Download
Update_DSCRX10V200.exe  (108.21 MB)

Download Files

Update_DSCRX10V200.exe
Date: 8/28/2014
Version: 2.00
Size: 108.21 MB
Download Now